Skip to content
 
 0

View CartCheckout

  • No products in the cart.

Subtotal: $0.00

View CartCheckout

EdanUSA
EdanUSA
888-850-4597info@edanusa.comMon. - Fri. 8:00AM - 5:00PM PST
  • Home
  • Products
    • Colposcopes
    • Dopplers
    • EKG Machines
    • Fetal Monitors
    • Holter Monitors
    • Patient Monitors
    • Pulse Oximeters
    • Ultrasound
    • Veterinary Equipment
    • Vital Sign Monitors
  • Service & Support
    • Service Center
      • Create a Support Ticket
      • Schedule Service Appointment
    • Learning Center
      • Brochure Library
      • Helpful Articles
      • Webinars
      • News & Events
  • Company
    • About
    • Contact

Get in Touch

  • Home
  • Products
    • Colposcopes
    • Dopplers
    • EKG Machines
    • Fetal Monitors
    • Holter Monitors
    • Patient Monitors
    • Pulse Oximeters
    • Ultrasound
    • Veterinary Equipment
    • Vital Sign Monitors
  • Service & Support
    • Service Center
      • Create a Support Ticket
      • Schedule Service Appointment
    • Learning Center
      • Brochure Library
      • Helpful Articles
      • Webinars
      • News & Events
  • Company
    • About
    • Contact

Yearly Archives: 2019

You are here:
  1. Home
  2. 2019

How to Prepare a SE-2003 Holter for Patient Use

CardiologyBy edanusaAugust 27, 2019Leave a comment

This is how you prepare the holter for patient use. Enter all of the patient’s information. Disconnect the cable and connect the holter. A screen will pop up after you connect the holter. Press the “M” button. This is just to check your channels — Channels 1, 2, and 3 — to make sure everything…

How to Install a Plate on the M3 Vital Sign Monitor

Vital Sign MonitoringBy edanusaAugust 22, 2019Leave a comment

How to install a plate on an M3 You will need a Phillips screwdriver, the M3 plate, and 3 additional screws. Remove the 3 screws from the bottom of the machine Align the plate  Line up the 3 additional screws to where you removed the original screws from  Screw them in.

How to Install Paper on an F2 Fetal Monitor

Fetal MonitoringBy edanusaAugust 20, 2019Leave a comment

How to Install Paper on an F2 Fetal Monitor To install your paper, make sure that the very first sheet of paper on the top is the red grid facing up To the left, you will see your FHR, to the right will be your TOCO. Open the door and  insert the paper under the…

How to Install a Printer on the iM8 Patient Monitor

Patient MonitoringBy edanusaAugust 16, 2019Leave a comment

In this video, I will show you how to install a printer on an iM8 monitor.  You will need a printer, paper, a phillips, a very small flathead, and 2 screws. To install the printer on the iM8, you will first need to remove the side panel. To remove the side panel, you will need…

How to Set Up Automatic Blood Pressure Readings and Trigger Printing for Patient Monitors

Patient MonitoringBy edanusaAugust 2, 2019Leave a comment

Blood pressure readings: Click into the NIBP section on the main screen to bring up the NIBP set up menu.   Change measure mode and inflation mode to AUTO Select the interval of your choice — 1-5 minutes, 10 minutes, 15 minutes, 30 minutes, 60 minutes, 90 minutes, or all the way up to every 480…

How to Set Up Automatic Blood Pressure Readings and Trigger Printing for M3 Vital Sign Monitor

Vital Sign MonitoringBy edanusaAugust 2, 2019Leave a comment

To set up Automatic Blood Pressure Readings: Go into the main system menu and select NIBP set up Turn inflation mode to auto and select the interval of your choice    To Set up Trigger Printing: To set NIBP trigger printing, go back to system menu, select maintain, and enter user password “9981” In the…

How to Set Pitch Tone Through the Spo2 Sensor on a Patient Monitor

Patient MonitoringBy edanusaAugust 2, 2019Leave a comment

On the main display, click into the ECG section to bring up the ECG setup menu Change “HR from” to SpO2. Go to the SpO2 section to bring up the SpO2 set up menu to make sure the pitch tone is turned on.  You can also increase or decrease the volume of the pitch tone…

How to Fix the “Loose Cuff” Error on a M3 Vital Sign Monitor

Vital Sign MonitoringBy edanusaAugust 2, 2019Leave a comment

Check the age parameters on the display banner on the top of the screen ADU stands for Adult PED stands for Pediatric  NEO stands for Neonate  Check that the cuff size you have entered in matches your patient type It needs to be set to ADU for adult cuff or PED with a child cuff. …

New iM3 Vital Sign Monitor Release

Product NewsBy edanusaJune 19, 2019Leave a comment

EdanUSA Releases Brand New iM3 Vital Signs Monitor [San Diego, CA, June 2019] – EdanUSA is pleased to announce the release of its brand new iM3 Vital Signs Monitor. Replacing the M3, the iM3 is taking the lead and presenting itself as the pioneer of a new and improved generation of vital signs monitors. The…

How to change the date & time of an EdanUSA patient monitor

Patient MonitoringBy edanusaJune 17, 2019Leave a comment

Here’s how to change the date and time on an Edan Patient Monitor. This will work with the iM50, 60, 70, and 80.    On the main screen, go to the Menu Go to “Maintenance” Go to “User Maintain” Type in the password “ABC” Click “Ok” to confirm Scroll down to the bottom Go to…

12
EdanUSA
EdanUSA 2023. All Rights Reserved.

mail: info@edanusa.comtel: 888 850 4597

Go to Top
Close X
×